Watch on YouTube: Slip Barrier Coats HOLD BLOCK: Dose per Hold and How to Spray
TL;DR
- Slip Barrier Coats HOLD BLOCK is a non-reactive emulsion sprayed on hold walls before loading; it dries into a thin barrier film.
- After discharge the film comes off with the cargo residue, so hold cleaning is quicker and turnaround is shorter.
- Typical smooth-surface dose per hold: sulphur or salt 100 L (Handymax), 150 L (Panamax); pet coke or coal 200 L and 250 L.
- One 210 L drum covers 2,000 to 2,500 m² of smooth, clean surface; rough or rusted steel needs more.
- Use it neat with a low-pressure machine or garden spray pump, after removing old cargo deposits and lime wash.
Slip Barrier Coats HOLD BLOCK is a non-reactive, emulsion-based coating that you spray on cargo hold walls before loading, so the cargo sits on a thin barrier film instead of on the paint. After discharge the film comes away with the residue, so the hold washes clean faster and the ship is ready for its next cargo sooner.
The video above shows the whole process. This page sets out the same steps in writing: why sulphur, salt, pet coke and coal damage a hold, how the film works, what to do if the walls are already caked, and how many litres to spray per hold on a Handymax or Panamax.
Why do sulphur, salt, pet coke and coal foul a cargo hold?
Corrosive cargoes attack the steel, and messy cargoes stick to the paint. Sulphur and salt bring rust to bare steel, while pet coke, coal and concentrates cling to the coating and work their way into it.
The cost shows up after discharge. The hold walls are still caked, the next cargo is waiting, and every extra hour of cleaning delays loading. For a superintendent or ship agent at Port Sultan Qaboos in Muscat, Sohar or Duqm, that cleaning time decides when the next loading can start.
How does a slip barrier coat protect the hold?
It puts a temporary film between the cargo and the paint. You spray the emulsion on, it dries into a thin barrier film, and the cargo touches that film rather than the coating underneath.
After discharge, the film comes off with the cargo residue, so hold cleaning is quicker and easier. The data sheet lists these benefits for this hold coating:
- Protects metal against corrosive cargo such as sulphur and salt.
- Protects paint against cargo penetration from pet coke, coal and concentrates.
- Safe on all coatings, and safe for the personnel handling it.
- Environmentally friendly, and safe to use in occupied or covered areas such as a closed hold.
- Reduces turnaround times.
What to do first if the hold is already caked
Clean the hold before you coat it, because the film has to go onto the hold surface, not onto old cargo. Remove the deposits of the previous cargo and any lime wash before spraying.
If the hold has been repainted, the new paint must be fully cured before HOLD BLOCK goes on. Our earlier overview of Slip Barrier Coats HOLD BLOCK covers the product range; the steps below cover the application.
How to apply Slip Barrier Coats HOLD BLOCK, step by step
Prepare the hold, spray the product neat at the right dose for the cargo, and wash it off after discharge. In order:
- Prepare the hold. Remove the previous cargo deposits and any lime wash. Check that any new paint is fully cured.
- Put on PPE. The product is safe to handle, but wear goggles, protective gloves and a mask as a precaution.
- Spray it neat. Use it directly from the drum with no mixing, applied with a low-pressure machine or by hand with a garden spray pump.
- Apply the dose for your cargo. Use the table below for a smooth surface, and allow more product on rough or rusted steel.
- Let the film form, then load. The emulsion dries into a thin barrier film, and the cargo goes onto that film.
- Wash after discharge. Once the cargo is out, the film comes off with the residue during hold cleaning.
How much HOLD BLOCK do you need per hold?
Typical doses for this type of hold coating on a smooth surface are 100 L per hold on a Handymax and 150 L on a Panamax for sulphur and salt, rising to 200 L and 250 L for pet coke and coal. The exact figure depends on your vessel, hold condition and cargo.
| Cargo | Handymax, per hold | Panamax, per hold |
|---|---|---|
| Sulphur, salt, etc. | 100 L | 150 L |
| Pet coke, coal, etc. | 200 L | 250 L |
One 210 L drum covers 2,000 to 2,500 m² of smooth, clean surface. Rough and rusted surfaces need more.
Planning a whole ship
For a five-hold Handymax, plan 500 to 1,000 L in total, about ½ to 1 drum per hold. For a seven-hold Panamax, plan 1,000 to 2,000 L in total, about ¾ to 1¼ drums per hold.
As a worked example, a Handymax loading pet coke in all five holds at 200 L per hold needs 5 × 200 L = 1,000 L, the top of the Handymax range. The same ship carrying salt at 100 L per hold needs 5 × 100 L = 500 L.
Which HOLD BLOCK part number to order
We list HOLD BLOCK under several part numbers. Send us the vessel type, number of holds and cargo, and we will confirm the version and pack size that fits your quantity.
| Part numbers | Slip Barrier Coats HOLD BLOCK, RXSOL-22-2210-210; RXSOL-22-2210-025; RXSOL-22-2210-050; PRELOAD Slip HOLD BLOCK, RXSOL-20-2210-210; EC Slip Barrier Coats HOLD BLOCK, RXSOL-25-2210-210 |
|---|---|
| Type | Emulsion-based, non-reactive coating that dries to a thin barrier film |
| Application | Cargo holds carrying sulphur, salt, pet coke, coal and concentrates |
| Typical dose | 100 to 250 L per hold on a smooth surface, by cargo and ship size |
| Coverage | 2,000 to 2,500 m² per 210 L drum, smooth, clean surface |
| Method | Neat, by low-pressure machine or garden spray pump |
| PPE | Goggles, protective gloves, mask |
Where to buy HOLD BLOCK in Muscat and Oman
Oman Chem (Muscat & Barka for Business Trading) supplies Slip Barrier Coats HOLD BLOCK from Barka Industrial Area, Sultanate of Oman. Call +968 77333599, message us on WhatsApp or email omanchem.com@gmail.com.
For a ship loading at Sohar, the same product is also listed on Sohar Chemical for Sohar port deliveries. You can browse our other marine and oilfield chemicals on the Oman Chem products page.
Frequently asked questions
What is Slip Barrier Coats HOLD BLOCK used for?
It is a heavy-duty protective coating for the holds of ships carrying corrosive or messy cargoes such as sulphur, salt, pet coke, coal and concentrates. It protects the steel and paint and makes cleaning after discharge quicker.
Do I need to dilute HOLD BLOCK before spraying?
No. Use it neat, straight from the drum, with a low-pressure machine or a garden spray pump.
How much HOLD BLOCK does a Panamax carrying coal need?
The typical dose is 250 L per hold on a smooth surface. A seven-hold Panamax needs 1,000 to 2,000 L in total depending on cargo and hold condition, and rough or rusted steel needs more.
Is it safe on existing hold paint?
Yes, it is safe on all coatings. New paint must be fully cured before you apply it.
How is the coating removed after discharge?
The film comes off with the cargo residue during normal hold cleaning, so the walls wash clean faster than an uncoated hold.