Watch on YouTube: Rust Remover for Steel: Less Grinding in 4 Steps
TL;DR
- RXSOL Rust Remover is a concentrated cleaner based on phosphoric acid that dissolves rust, so you do much less grinding.
- On steel: clear loose material, dilute 10-50 % in water, brush on, leave 5-40 min, rinse with a clean water jet.
- On aluminium, use 10-25 % only and rinse within 10-30 min.
- Always add the product to the water, never water to the product. Wear eye protection and PVC gloves.
- Neutralise rinse water with lime powder to pH 6-10 before it goes to a drain.
RXSOL Rust Remover is a concentrated, acid-based cleaner. It soaks into rust and dissolves the iron oxide, so you can clean steel with far less grinding and scraping. First clear off loose material. Then dilute the product 10-50 % in water, brush it on, leave it for 5-40 min and rinse with a clean water jet.
This page sets out the method in four steps. It adds the figures for aluminium and stainless steel, the safety rules and the part numbers to quote when you order in Muscat. If you are new to the product, our overview of what rust remover is used for covers the basics.
Why grinding rust off by hand slows the job
Grinding rust off by hand is slow, hard work. On a pipe run, a tank wall or a tray of small fittings, a grinder seldom reaches the bottom of every pit. Salt, air and water keep bringing the rust back on ships, in shipyards and workshops, and on the structures, machinery, pipelines, tanks and tools that contractors maintain from Duqm to Nizwa.
A chemical rust remover does most of the loosening for you. You still take off the loose flakes, but the product dissolves the bonded oxide in the pits, so you do not have to grind it out.
How rust remover works on iron oxide
Rust remover reacts with the rust and dissolves it. Our product is based on phosphoric acid, with an ethoxylated fatty alcohol and a detergent. The data sheet describes it as a blend of corrosion inhibitors and surface-active emulsified acidic materials.
The liquid soaks into the cracks in the rust layer and reacts with the iron oxide, which loosens and dissolves it. It also removes mineral scale, corrosion deposits and oxidation from ferrous metal. Use it on steel and on other surfaces that acid does not harm.
How to remove rust from steel in 4 steps
For most rusted steel, brush the product on at a dilution of 10-50 %. Small parts can be soaked instead.
- Prepare the surface. Remove loose rust, flaking paint, dirt and oil before you apply anything. If the part is also oily or greasy, ask us whether our Degreaser And Deruster suits the job.
- Mix in a plastic container. Dilute the concentrate 10-50 % in water. Always add the product to the water, never water to the product. Wear eye protection and PVC chemical-resistant gloves from this step onwards.
- Brush it on and wait. Apply by brush and let it react for 5-40 min. Small objects, such as hand tools and fabricated components, can be soaked in a plastic container instead.
- Rinse. Rinse the surface thoroughly with a clean water jet.
For more on mixing and handling, read our rust remover dosage and safety guide.
Before you paint: neutralise and prevent flash rust
Protect clean steel straight away, because bare steel can flash-rust before the primer goes on. After rinsing, neutralise the surface where your paint system calls for it, then apply the primer or protective coat.
Removing rust before painting is a popular use for this product. In humid coastal air at Muscat, Sohar or Duqm, have the primer ready before you start the rinse, so the bare steel is not left standing.
Aluminium, stainless steel and painted surfaces
Each surface needs its own dilution and contact time. The figures below come from our data sheet.
| Surface | Method |
|---|---|
| Steel | Dilute 10-50 %, apply by brush, react 5-40 min, rinse thoroughly with a clean water jet |
| Small parts | Soak in a plastic container, then rinse with a water jet |
| Aluminium | Only 10-25 %, rinse within 10-30 min |
| Stainless steel | 1 part to 4-10 parts water, immerse 1-3 h; faster with heat up to 60 °C and agitation |
| Rust stains on paintwork | Removes rust stains without risk to the paintwork; ask us for the TDS before you mix |
We also list Rust Remover Safe and Oxalic Acid Rust Remover. Tell us the metal and the job, and we will tell you which product to order.
Safety, handling and drain disposal
The product will not burn, but it is an acid and it causes burns to skin and eyes. Use the following controls on every job.
- Wear eye protection at all times and use PVC chemical-resistant gloves. Keep an eyewash at the workplace.
- Dilute only in a plastic container, and add the product to the water, never water to the product.
- Keep it away from alkaline materials.
- Before rinse water goes to a drain, neutralise it with an alkaline material such as lime powder to pH 6-10.
- For transport it is IMDG class 8, UN 1805 (phosphoric acid).
Rust remover specifications and part numbers
| Part numbers | RXSOL-16-1088-025, RXSOL-16-1088-210 |
|---|---|
| Packing | 25 L, 210 L and 1000 L |
| Type | Concentrated, acid-based cleaning and descaling compound (phosphoric acid) |
| Application | Rust, iron oxide, corrosion deposits and mineral scale on steel structures, machinery, pipelines, tanks and tools |
| Dilution on steel | 10-50 %, 5-40 min |
| Appearance | Clear, colourless liquid |
| pH | 1.5-2.5 (10 % solution) |
| Flash point | None, non-combustible |
| Transport | IMDG class 8, UN 1805 |
| TDS and MSDS | On request |
Where to buy rust remover in Muscat and Oman
Oman Chem (Muscat & Barka for Business Trading) supplies RXSOL Rust Remover from Barka Industrial Area, Sultanate of Oman. Call +968 77333599, message us on WhatsApp or email omanchem.com@gmail.com. Tell us your site and we will confirm how we can supply it.
For jobs in the north, the same product is also listed on our Sohar site for Sohar port and industrial area orders. You can see the rest of our range on the Oman Chem products page.
Frequently asked questions
Does rust remover work without grinding?
It dissolves bonded rust, so you need far less grinding and scraping. Remove loose rust, flaking paint, dirt and oil before you apply it.
Can I use rust remover on aluminium?
Yes, at a weaker mix. Use only 10-25 % and rinse within 10-30 min.
How long should I leave rust remover on steel?
At 10-50 % dilution, let it react for 5-40 min, then rinse thoroughly with a clean water jet.
Can the rinse water go down the drain?
Only after neutralising it. Use an alkaline material such as lime powder to bring it to pH 6-10.
Which pack sizes can I order?
We supply 25 L, 210 L and 1000 L packs. Quote part number RXSOL-16-1088-025 or RXSOL-16-1088-210 when you order.