Watch on YouTube: Paint Remover Chemical for Metal: Strip Epoxy & Enamel Without Grinding | RXSOL

TL;DR

  • Brush, dip or spray Paint Remover 5 Ltr on painted metal, wait until the paint wrinkles and lifts, then scrape it off.
  • It removes paint, varnish, lacquer, baked enamel, shellac and epoxy without grinding or sanding.
  • It does not attack steel, aluminium, copper, brass or their alloys.
  • Use it as supplied. No dilution and no fixed dwell time: watch the surface.
  • Contains dichloromethane, signal word DANGER: ventilation, nitrile or PVC gloves, goggles, keep off rubber.

Paint Remover 5 Ltr (part number RXSOL-18-1013-005) is a solvent-based paint stripper for metal. You brush it on, wait until the coating wrinkles and lifts, then lift it away. There is no grinding or sanding. It removes paint, varnish, lacquer, baked enamel, shellac and epoxy, and it does not attack steel, aluminium, copper, brass or their alloys.

The video above shows three ways to use it in a workshop: brushing a painted panel, dipping small parts and spraying a motor housing. Below are the same steps in writing, with the safety points and the part numbers to put on your order.

Why strip paint chemically instead of grinding

A chemical stripper removes the coating and leaves the metal underneath intact. Grinding paint off a panel can scar the steel. On a pump casing, valve body or motor frame, that damage is hard to repair.

Buyers choose this type of stripper when grinding or blasting is impractical or would damage the part. It is used in shipping, garages, paint shops and industrial plant maintenance. The aircraft industry uses it because it leaves steel, aluminium, copper and brass unharmed.

How Paint Remover 5 Ltr works on metal

The liquid soaks down through the coating. Our technical data sheet describes two actions. Penetrating agents attack the paint film, and organic components leave a protective film on the metal.

On a plain surface, the paint wrinkles and lifts away quickly in large sheets. Phosphated, chromated or anodised parts strip more slowly and the coating comes off in small pieces. Heavily pigmented coatings behave the same way, so allow those parts more time.

The product is a clear, colourless liquid. Use it as supplied. There is no dilution step.

Step by step: brush, dip or spray

Choose the method by the size of the part.

Brush or wipe large parts

  1. Move the part to a well-ventilated area or outdoors. Put on nitrile or PVC gloves, goggles or a face shield, and protective clothing.
  2. Remove or cover rubber seals and hoses, because rubber may swell on contact.
  3. Apply a full coat with a brush, rag or sponge. Test synthetic brushes and sponges on a small area first.
  4. Let it work until the paint wrinkles and lifts. The data sheet gives no dwell time, so watch the surface rather than the clock.
  5. Remove the softened coating, then wipe the metal clean.

Dip small parts

  1. Fill an open tank and lower the small parts in.
  2. Agitate gently to help the stripping. Do not use strong air agitation, because it causes the solvent to evaporate.
  3. Lift the parts out and wipe them dry with a rag or blow them dry.
  4. Cover the tank after use. You can reuse the solution.

Spray large equipment

Use a coarse spray on large items such as generators and large electric motors. Collect the run-off so you can use it again.

Paint Remover 5 Ltr specification

ItemDetail
Part numberRXSOL-18-1013-005
TypeSolvent-based paint stripper, clear colourless liquid
RemovesPaint, varnish, lacquer, baked enamel, shellac, epoxy
Safe onSteel, aluminium, copper, brass and their alloys
ApplicationMetal parts, automobiles, trucks, ship parts, generators, electric motors
MethodsBrush or wipe, dip tank, coarse spray
DilutionUse as supplied
Packing5 litre
ContainsDichloromethane (methylene chloride, CAS 75-09-2)
MSDS / TDSOn request

Where it fits on Oman oilfield and plant jobs

If you maintain equipment for oilfield contractors in Duqm, Nizwa or the interior, the usual jobs are repaints and overhauls. Typical items are motor housings, generator frames, pump casings, valve bodies and truck panels. You can strip these without grinding.

Brass and aluminium fittings can go into the same dip tank as steel bolts, because the stripper does not attack those metals. Garages in Muscat can use it on automobiles and trucks before a respray.

Plan for the heat in Oman. Keep containers closed, out of the sun and away from heat, and store them somewhere cool. Covering your dip tank after each shift also cuts losses from evaporation.

Safety: dichloromethane and PPE

This paint remover contains dichloromethane, also called methylene chloride (CAS 75-09-2). The RXSOL-18-1013-025 safety data sheet lists it at 30-60 %, and the product carries the signal word DANGER.

  • Work in a well-ventilated area or outdoors, and do not breathe the vapour.
  • Wear solvent-resistant gloves (nitrile or PVC), goggles or a face shield, and protective clothing.
  • Keep the container closed, keep it away from heat and store it cool.
  • Keep it off rubber seals and hoses.

Ask us for the MSDS before your first job so your site safety officer can approve the work method.

Which RXSOL paint remover to order

For metal parts and vehicle panels, order Paint Remover 5 Ltr (RXSOL-18-1013-005). The same solvent-based family also includes Paint Remover RXSOL-18-1013-025 and Paint Remover Solvent Based RXSOL-18-1013-010.

Masonry and graffiti need a different product. Paint Remover MC (RXSOL-18-1805-025) is a thixotropic alkaline remover with a 45 min-2 h dwell. For soaking parts that carry both carbon deposits and paint, use RXSOL 664 Immersion Carbon and Paint Remover (RXSOL-18-1811-025).

Where to buy Paint Remover 5 Ltr in Muscat

Oman Chem (Muscat & Barka for Business Trading) supplies from Barka Industrial Area, Sultanate of Oman. Call +968 77333599 or message us on WhatsApp with the part number and quantity. We will confirm delivery from Barka to your workshop or site in Muscat.

The same part number is also listed on our Sohar site and on Muscat Chemical. For degreasers, solvents and other workshop chemicals for the same job, see our full product list.

Frequently asked questions

Will Paint Remover 5 Ltr damage aluminium or brass?

No. It does not attack steel, aluminium, copper, brass or their alloys, which is why the aircraft industry uses this type of stripper.

How long do I leave it on?

The data sheet gives no fixed time. Leave it until the paint wrinkles and lifts. Phosphated, chromated, anodised or heavily pigmented coatings take longer and come off in small pieces.

Can it remove epoxy and baked enamel?

Yes. It removes paint, varnish, lacquer, baked enamel, shellac and epoxy.

Can I reuse the stripper?

Yes, if you use a dip tank or spray. Cover the dip tank after use and reuse the solution. When you spray, collect the run-off and use it again.

What protection do my workers need?

Work in good ventilation or outdoors. Wear nitrile or PVC gloves, goggles or a face shield, and protective clothing. The product contains dichloromethane and carries the signal word DANGER.