Watch on YouTube: Superplasticizer for Concrete: Don't Add Water at Site | RXSOL

TL;DR

  • Do not add water to a stiff load at site: it raises the water-cement ratio and costs strength and durability.
  • A superplasticizer disperses the cement particles, so the mix flows without extra water or keeps its slump with less water.
  • Start trial mixes at 0.7 to 1.5 litres per 100 kg of cement, then set the working dose by trials.
  • Add it with the gauging water during mixing, never to dry cement.
  • It slows the set, so check early strength before you strip the formwork.

When a ready-mix load arrives too stiff to pump, do not reach for the water hose. Extra water raises the water-cement ratio and costs you strength and durability, so the better fix is a superplasticizer admixture for concrete, dosed at the batching plant. It disperses the cement particles, which lets the same mix flow without extra water.

The video above shows this happening on a site, then goes back to the batching plant to show the better way. This page covers the same steps in writing: the starting dose, how to add the admixture, how it behaves in hot weather, and the mistakes that cause trouble on pours in Muscat, Duqm and Nizwa.

Why adding water at site is the wrong fix

Adding water to a stiff load changes the water-cement ratio the mix was designed for. A higher water-cement ratio costs you strength and durability, even if the load now pumps.

The stiffness has a cause. In a fresh mix, cement grains clump together and hold water back, so the mix needs more water just to move. A superplasticizer breaks up those clumps, so you do not need to thin the paste with water.

How a superplasticizer admixture for concrete works

The admixture disperses the cement particles, so the water already in the mix does more work. You can use that in two ways: more workability at the same water content, or less mixing water at the same slump.

Our Super Plasticizer Admixture for Concrete, part number RXSOL-67-6704-210, is a brown liquid made by RXSOL. It is chloride-free and is used in ready-mix, precast and reinforced concrete.

A lower water-cement ratio supports strength and helps you get dense, low-permeability concrete for basements and for underground and overhead water tanks. Final strength still depends on the complete mix design, placing and curing.

A cohesive, flowing mix pumps well and fills walls, columns and congested reinforcement with less segregation and bleeding. It can also help you economise on cement. It is useful as part of a self-compacting concrete design, but a superplasticizer alone does not make a mix self-compacting.

ItemDetail
Part numberRXSOL-67-6704-210
FormBrown liquid, chloride-free
ApplicationReady-mix, precast and reinforced concrete; pumping; walls, columns and congested reinforcement; low-permeability concrete for basements and water tanks
How it worksDisperses the cement particles; also retards setting
Starting dose0.7 to 1.5 litres per 100 kg of cement, as a starting range for trial mixes
How to addWith the gauging water during mixing
HandlingWear gloves and safety glasses; wash splashes off with plenty of water

How to dose and add it at the batching plant

Start your trial mixes at 0.7 to 1.5 litres per 100 kg of cement, then set the working dose by trials with your own materials. That range is only a starting point for trials.

  1. Set your targets. Fix the target slump, water-cement ratio, transport time and strength for the job.
  2. Run trial mixes. Test slump, slump retention, setting and strength using the cement, SCMs, aggregates and water you will use on the job, at the temperature and humidity the pour will see.
  3. Calculate the dose from the cement content. Divide the cement in the batch (kg) by 100 and multiply by your trial dose in litres. Measure it accurately.
  4. Add it with the gauging water. Meter the measured dose into the gauging water during mixing. Never add it to dry cement.
  5. Mix thoroughly, then check. Check the slump before you pour.
  6. Record the results. Keep the dose and test results for each mix design.
  7. Repeat trials when materials change. A new cement, a new sand source or a change in temperature means new trials.

Safety: wear gloves and safety glasses, and wash any splash off with plenty of water.

Can you add it at site into the truck?

Yes, if you agree the procedure with your concrete producer first. The admixture can also go in near the end of mixing, or into the truck at the job site. Then mix thoroughly at a higher drum speed with more revolutions before you discharge.

Using it in hot weather on Oman sites

The admixture slows the set, so ready-mix stays workable for longer during transport in hot weather. Workability retention is up to 2 to 3 hours under suitable conditions. Temperature, cement, transport and mix design all change that, so treat it as something to confirm in your trials, not a fixed delivery allowance.

This matters on long summer hauls, for example from a batching plant to a project in Duqm or to a site in the interior around Nizwa. Build the real haul time into your trial mixes and test slump retention over that same period.

Because it retards, check early strength before you strip formwork from walls and columns. A flowing mix still needs a poker vibrator for compaction and proper curing afterwards.

Mistakes that cost you strength

  • Adding water whenever the mix looks stiff. It changes the water-cement ratio of a designed mix.
  • Copying another product's dose. Start from our range and set the dose by your own trials.
  • Confusing litres with a percentage. Our starting range is litres per 100 kg of cement.
  • Assuming longer workability means the setting time is unchanged. It retards, so check early strength before stripping forms.
  • Adding it to dry cement. It goes in with the gauging water.
  • Relying on flow instead of compaction and curing. Vibrate and cure as your specification requires.

Where to buy in Muscat and across Oman

Oman Chem (Muscat & Barka for Business Trading) supplies RXSOL-67-6704-210 from Barka Industrial Area to ready-mix plants, precast yards and contractors in Muscat and across Oman. Call +968 77333599 or message us on WhatsApp. We confirm pack size and delivery to your site in the quote.

The same admixture is also listed on Sohar Chemical. See also our super plasticizer supply page for Sohar, Muscat, Barka, Ruwi and Madayn. You can find other products in our full product range.

Frequently asked questions

How much superplasticizer do I add per 100 kg of cement?

Start your trial mixes at 0.7 to 1.5 litres per 100 kg of cement. Then set the working dose by trials with your actual cement, aggregates, water, temperature and target slump.

Can I add superplasticizer to the truck at site?

Only if you agree the procedure with your concrete producer. After adding it, mix thoroughly at a higher drum speed with more revolutions before you pour.

Does a superplasticizer delay the setting of concrete?

This one does. It retards setting, which keeps ready-mix workable for longer in hot weather, so check early strength before you strip formwork.

Can it be used in reinforced concrete?

Yes. It is chloride-free and is used in ready-mix, precast and reinforced concrete, including congested reinforcement in walls and columns.

What protection do I need when handling it?

Wear gloves and safety glasses, and wash any splash off with plenty of water.