Boiler Chemicals

Oxygen Control

Chemical Oxygen Scavengers. The oxygen scavengers most commonly used in boiler systems are sodium sulfite, sodium bisulfite, hydrazine, catalyzed versions of the sulfites and hydrazine, and organic oxygen scavengers, such as hydroquinone and ascorbate.

It is of critical importance to select and properly use the best chemical oxygen scavenger for a given system. Major factors that determine the best oxygen scavenger for a particular application include reaction speed, residence time in the system, operating temperature and pressure, and feedwater pH. Interferences with the scavenger/oxygen reaction, decomposition products, and reactions with metals in the system are also important factors. Other contributing factors include the use of feedwater for attemperation, the presence of economizers in the system, and the end use of the steam. Chemical oxygen scavengers should be fed to allow ample time for the scavenger/oxygen reaction to occur. The deaerator storage system and the feedwater storage tank are commonly used feed points.

In boilers operating below 1,000 psig, sodium sulfite and a concentrated liquid solution of catalyzed sodium bisulfite are the most commonly used materials for chemical deaeration due to low cost and ease of handling and testing. The oxygen scavenging property of sodium sulfite is illustrated by the following reaction:

Theoretically, 7.88 ppm of chemically pure sodium sulfite is required to remove 1.0 ppm of dissolved oxygen. However, due to the use of technical grades of sodium sulfite, combined with handling and blowdown losses during normal plant operation, approximately 10 lb of sodium sulfite per pound of oxygen is usually required. The concentration of excess sulfite maintained in the feedwater or boiler water also affects the sulfite requirement.

Sodium sulfite must be fed continuously for maximum oxygen removal. Usually, the most suitable point of application is the drop leg between the deaerator and the storage compartment. Where hot process softeners are followed by hot zeolite units, an additional feed is recommended at the filter effluent of the hot process units (prior to the zeolite softeners) to protect the ion exchange resin and softener shells.

As with any oxygen scavenging reaction, many factors affect the speed of the sulfite-oxygen reaction. These factors include temperature, pH, initial concentration of oxygen scavenger, initial concentration of dissolved oxygen, and catalytic or inhibiting effects. The most important factor is temperature. As temperature increases, reaction time decreases; in general, every 18°F increase in temperature doubles reaction speed. At temperatures of 212°F and above, the reaction is rapid. Overfeed of sodium sulfite also increases reaction rate. The reaction proceeds most rapidly at pH values in the range of 8.5-10.0.

The following operational conditions necessitate the use of catalyzed sodium sulfite:

• low feedwater temperature
• incomplete mechanical deaeration
• rapid reaction required to prevent pitting in the system
• short residence time
• use of economizers

High feedwater sulfite residuals and pH values above 8.5 should be maintained in the feedwater to help protect the economizer from oxygen attack.

Some natural waters contain materials that can inhibit the oxygen/sulfite reaction. For example, trace organic materials in a surface supply used for makeup water can reduce speed of scavenger/oxygen reaction time. The same problem can occur where contaminated condensate is used as a portion of the boiler feedwater. The organic materials complex metals (natural or formulated catalysts) and prevent them from increasing the rate of reaction.

Sodium sulfite must be fed where it will not contaminate feedwater to be used for attemporation or desuperheating. This prevents the addition of solids to the steam.

At operating pressures of 1,000 psig and higher, hydrazine or organic oxygen scavengers are normally used in place of sulfite. In these applications, the increased dissolved solids contributed by sodium sulfate (the product of the sodium sulfite-oxygen reaction) can become a significant problem. Also, sulfite decomposes in high-pressure boilers to form sulfur dioxide (SO2) and hydrogen sulfide (H2S). Both of these gases can cause corrosion in the return condensate system and have been reported to contribute to stress corrosion cracking in turbines. Hydrazine has been used for years as an oxygen scave

RXSOL-50-5004-020  is dependent on boiler operating condition, Feed 200 gm to 1 Kg  of RXSOL-50-5004-020 solution for per thousand Ltr of boilers water Then control  the  system by  Periodic Alkalinity  test procedure.  FREE LOGSHEET is available for our registered member. ( Maintaining of Logsheet allow to observing and evaluating the test results trend in order to use the exact amount needed for the stabilization of the system
If p-Alkalinity is below 200  ppm  increase the  ratio of  RXSOL-50-5004-020  solution. If  p-Alkalinity  is above  400 ppm  reduce  the  concentration of  RXSOL-50-5004-020  solution by dilution with water.          

RXSOL ALKALINITY, PHOSPHTE and SULFITE TEST KITS are available on request.

USES PROCEDURE : Always dissolve powder before feeding in BOILER WATER TANK.

Control Procedure:-

Control is by simple  boiler water tests or RX CLEANSERS  can provide a suitable test  kits for this purpose

RXSOL-50-5007-025 is a powerful oxygen scavenger in liquid sulphite form suitable for low and medium pressure boilers. The reaction of RXSOL-50-5007-025 with oxygen is catalysed ensuring the rapid absorption of oxygen to protect feedlines and boilers from corrosion

RXSOL-50-5005-025 alkaline and the vapors are irritating to eyes and lungs. Avoid contact with eyes and skin. Do not take internally. Observe safety regulations wear Goggles, PVC gloves and Apron when handling Provide ample ventilation Avoid contact with skin in case of contacts wash with cupious amount of water immediately. If eyes are splashed give immediate and prolonged irrigation with clean running water and obtain medical attention.

Wear safety glasses. The working area must be well ventilated to prevent the build-up of toluene vapour. Make sure that any sources of ignition, such as Bunsen burners, hot plates and hot air guns, are removed before you start work.

Eye contact: Immediately flush the eye with plenty of water. Continue for at least ten minutes and call for medical help. Skin contact: Wash off with soap and water. Remove any contaminated clothing. If the skin reddens or appears damaged, call for medical aid. Note that clothes soaked in toluene will be very flammable, so should be removed in an area in which there is no risk that they might catch fire. If swallowed: Call for immediate medical help.