Your shopping cart is empty.
Antiscalant for the protection of RO MEMBRANE. This is a reverse osmosis membrane treatment chemicals. It is highly concentrated polymer chemicals. Antiscalant Manufacturer, supplier and Exporter.
RO antiscalant
Scaling is caused in membranes because the level of hardness salts in the water becomes highly concentrated as it passes through the RO unit. In smaller units scale formation can be prevented by base exchange softening the make-up water but for larger systems that is very expensive. We have developed a range of easy to handle, cost-effective RO Antiscalant which increase the solubility of the hardness salts so they remain in solution rather than forming scale on the membrane. Our cost-effective RO antiscalants will inhibit a wide range of foulants including calcium carbonate, calcium sulphate, barium sulphate, strontium sulphate, calcium fluoride, silica and iron.
RO Antiscalants are dosed directly to the RO feed water tank or feedwater line (after pretreatment) at the recommended dosage of 1-3 mg/L and maximum dosage at 8mg/L, subject to inlet water quality and parameters is respect of Calcium Hardness, Iron, TDS, Alkalinity, pH and silica content. Maximum dilution should be 10% with RO or DI water for temperature less than 30 deg C. For higher temperature the dilution ratio can increase.
The typical dosage range is between 2 to 5 ppm or Typical dosage range is between 2 and 6 mg/L.
Dilution:
This product is formulated to be injected neat. However, if a dilution is required, use demineralized or RO permeate water. If neither of these is available, softened water may be substituted. The dilution for Vitec 1000 should not result in a solution strength of less than 10%. This guidelin will protect the effectiveness of the internal bacteriostat which inhibits bacterial growth in the drum and feed tank.Maximum dilution is temperature related as shown below.
Temperature, °C Maximum Dilution, %
<30 12
30-35 25
>35 50
Inhibit scale formation and effectively controls corrosion
Protects the membrane efficiently
Can be used neat or diluted
Enhance the plant operation and equipments life span
Tolerant to oxides of iron, aluminium etc
Economical
Compatible with almost all RO membranes
Easy in usage and handling
Excellent results as a replacement for softener filters
Highly effective for scale prevention from calciumcarbonate, calcium sulfate, barium sulfate, and strontium sulfate
Cleans the membrane surface by dispersing foulants
Works on wide range of pH
It reduces the risk of scaling and eliminates the use of hazardous acids, resulting in efficient plant operation with highest possible conversion rate.
It is a very effective antiscalant. It is also compatible with RO CHEMICALS series of coagulant and flocculants (polyelectrolytes). Our RO Antiscalant (HIGH PH) is effective in minimizing scaling in presence of foulants like Calcium Carbonate, Sulfate salts of Calcium, Barium, Strontium and Magnesium, Calcium Fluoride, Iron and Silica.
Our RO Antiscalant is dosed directly to the RO feed water tank or feed water line (after pretreatment) at the minimum recommended dosage of 1ppm and maximum dosage at 15ppm, subject to inlet water quality and parameters is respect of Calcium Hardness, Iron, TDS, Alkalinity, pH and silica content.
In case of high iron content of about 0.5 to 1.0ppm, the dosing has to be increased by 10-15ppm for stabilizing Calcium.
At about 10-15ppm dosage our RO Antiscalant (HIGH PH) is capable of fully inhibiting iron and calcium, and silica up to 166ppm. For higher silica content RXSOL ANTISCALANT should be used.
Antiscalant RO RXSOL-33-3302-025
Antiscalant C.I ALKA RXSOL-33-2034-025
Membrane Antiscalant ALKA 191T RXSOL-33-3321-030
Antiscalant ORG EV 2030 RXSOL-33-3325-230
Antiscalant RXSOL ORG EV RXSOL-33-3327
Performance:
This product offers a variety of critical performance and application benefits: Inhibits RO membrane scaling caused by the following:
| Calcium Carbonate: | CaCO3 |
| Calcium Sulfate: | CaSO4 |
| Barium Sulfate: | BaSO4 |
| Strontium Sulfate: | SrSO4 |
| Calcium Fluoride: | CaF2 |
Inhibit scale formation and effectively controls corrosion
Protects the membrane efficiently
Can be used neat or diluted
Enhance the plant operation and equipments life span
Tolerant to oxides of iron, aluminium etc
Economical
Compatible with almost all RO membranes
Easy in usage and handling
Excellent results as a replacement for softener filters
Highly effective for scale prevention from calciumcarbonate, calcium sulfate, barium sulfate, and strontium sulfate
Cleans the membrane surface by dispersing foulants
Works on wide range of pH
Key Features and Benefits