Primary tabs

Educational Use Only - Order On Request
LIQUIVAP TREAT
Get MSDS Get Technical Bulletin Connect on WhatsApp Request Info
Product Code: RXSOL-60-6001-210

Categories

Boiler Chemicals-42

Product Description

VapourTreatment  For controlling of Scale & Foam ::: Neutral Liquid for prevention of scale in seawater Evaporators
This is a highly Active Antifoulant, Water Scale Inhibitor, Dispersant and Anti-precipitant compound for use in industrial and Marine Water systems, such as cooking systems, Heat Exchangers, air conditioning equipment, etc.

Product Short Description

Boiler water treatment product, formulated with polymer scale inhibitors, alkaline compounds, phosphates and condensate protecting amines.

Product Application

Procedure Of Use and Dose Rates: POLYELECTROLYTE  polymer  of RXSOL-51-6001-025 reacts with the potential scale forming salts in the water to prevent them from adhering to heat transfer surfaces. These solids are held in suspension and  easily removed  from  the evaporator  line. Finally RXSOL-51-6001-025 also have defoaming properties by which will stop foaming in EVAPORATOR. And by that way Distilled water quality is maintained in side the EVAPORATOR.

Used in both high and low pressure evaporators. 

Product Dose

Dosage :

Daily Out Put Evaporator Daily  RXSOL VT 6001 Requirement
10 -20 MT 100-200 ML
30-40 MT 300-400 ML
50-60 MT 500-600



Setting the Flow Rate: The treatment is added to the dosage tank and mixed with water. Example: With the 0.5 litres of Vaptreat add sufficient water to make up 50 litres of liquid.The standard flow meter is Adjustable-Rate=0-l00ml/minute.Flow rate calculation: Flowrate = 50 Litres/24 x 60= 35 ml/min setting  i.eThis will last 24 hours.

Note: We can remove  existing  mineral scale deposits  by using  A  5-10%  solution of  RXSOL-51-6001-025 Otherwise to save money and cleaning of HARD DEPOSITS which is formed due to not proper treratment of Evaporator, we have specialized Safe Scale Remover with Indicator ( Product code is RXSOL-22-2210-200 ).

Product Note

What is LIQUIVAP TREAT?

LIQUIVAP TREAT is a high-performance, polymer-based scale inhibitor specifically designed for seawater distillation plants, including multi-stage flash (MSF) and multi-effect distillation (MED) systems. It is a concentrated liquid formulation based on polymaleic acid, engineered to control alkaline scale deposits such as calcium carbonate (CaCO₃) and magnesium hydroxide (Mg(OH)₂).
 

Why Is LIQUIVAP TREAT Important?

In seawater distillation, scale formation on heat transfer surfaces severely affects:

  • Thermal efficiency

  • Production output

  • Operating costs

  • Equipment longevity

LIQUIVAP TREAT is vital because it:

  • Prevents scale formation by dispersing and sequestering alkaline materials before they crystallize

  • Enhances heat exchange efficiency

  • Reduces energy consumption and downtime

  • Prolongs plant equipment lifespan

 

Role of LIQUIVAP TREAT in Seawater Distillation Plants

Core Functions:

 

  1. Scale Control: Inhibits formation of hard scales like calcium carbonate and magnesium hydroxide.

  2. Polymeric Action: The polymaleic acid blend interferes with crystal growth and keeps potential scale-forming compounds in suspension.

  3. Surface Protection: Reduces deposition on evaporator tubes and heat transfer surfaces.

  4. Anti-Foaming Support: Helps prevent foaming when used in synergy with anti-foam agents, ensuring smoother operation.

 

 

Effective For:

  • Multi-stage flash distillation (MSF)

  • Multi-effect distillation (MED)

  • High and low-pressure evaporators

  • Saltwater and brackish water systems

 

 

Where Can LIQUIVAP TREAT Be Used?

LIQUIVAP TREAT is ideal for:

  • Power & desalination plants

  • Marine distillation units (ships, rigs)

  • Industrial water recovery systems

  • Municipal seawater desalination projects

It is suitable for use in:

  • High-pressure evaporators

  • Low-pressure evaporators

  • Systems requiring continuous anti-scaling treatment

 

 

Summary of Benefits

 

Feature Benefit
Polymaleic acid base Strong inhibition of CaCO₃ & Mg(OH)₂
Liquid concentrate format Easy dosing and mixing
Thermal stability Effective across wide temperature range
Low molecular weight Ideal for fast-acting dispersion
Wide applicability Compatible with all major plant types

 

LIQUIVAP TREAT is more than just a scale inhibitor — it’s an essential component in protecting your distillation investment. Regular use ensures:

  • Stable plant output

  • Reduced maintenance

  • Improved water quality

  • Lowered operational costs

By controlling alkaline scale before it forms, LIQUIVAP TREAT plays a critical role in maximizing efficiency and uptime in any seawater distillation operation.

Industrial area

Why Evaporator Treatment Chemicals must use?

PREVENTION OF SCALING IN SEA WATER EVAPORATORS.
RXSOL Vapor Treatment Prevents scale formation at temperatures up to 160°C Also Reduces foaming and maintains optimum plant performance.
 

During distilled water production in seawater evaporators, SCALE CONTROL is very important to increase efficiency of distillation as the seawater contains large quantities of salt which is resulting SCALE FORMATION in heat transfer surfaces.  Scale deposits Not only lower plant efficiency by resisting the transfer of heat, But also damaging instruments. Routine use of RXSOL Vapor Treatment prevents Scale formation in the Evaporator SYSTEM.

Whats the Dose Ratio of RXSOL VAPOR TREATMENT Chemicals?

Dilute the RXSOL VAPOR TREATMENT chemicals with water and continuously inject via evaporator inlet or the salt water supply lineand dose into the evaporator system. 30 ml Dose per ton of Seawater is recommended for the prevention of scaling in seawater evaporators. Dose can vary  depends on the capacity and the operating conditions of the evaporator.
Note: for the gradual removal of existing scale deposits, at least twice the normal dose must be used. Remove deposits of more than 2mm, with Descalex Liqui

Remarks

RXSOL-51-6001-025 is a concentrated  solution of a POLYELECTROLYTE  polymer and Antifoaming Agents for  use in SEA WATER evaporator  as a controller of scale and foam in side the  evaporators.  It can be used as a scale inhibitor  in the  feed water  to EVAPORATORS producing fresh water .

A liquid polymer-based evaporator treatment specially designed to control and prevent scale formation in evaporators
 

whats the Importance of LIQUIVAP TREAT ?
LIQUIVAP TREAT used in Sea Water Distillation Plant to control Alkaline SCALE due to presence of Alkaline Materials like calcium carbonate and magnesium hydroxide.
 
What is the role of LiquiVAP Treat in Seawater distillation Plant ?
Water blend of Polymaleic acid. LIQUIVAP TREAT is a highly concentrate liquid product to prevent scaling in all types of seawater distillation plant. LIQUIVAP TREAT is a concentrated formula polymeric scale inhibitor of low molecular weight for the prevention of scale in salt or fresh water, flash

Where LIQUIVAP TREAT can be used ?
For use with both high and low pressure evaporators to help: • Prevent scale formation. • Prevent foaming
 
 
 
LIQUIVAP TREAT is a liquid product for the control of alkaline scaling (calcium carbonate and magnesium hydroxide) in all types of seawater distillation plant.

Other Equivalent Brand

LIQUIVAP HC 130, OPTITREAT 25 Ltr

Product Tag Identification

Evaporator Treatment is used to stop scale buildup in high and low pressure evaporators system.

Product Useful Area

LIQUIVAP TREAT is an advanced liquid boiler water treatment product, formulated with polymer scale inhibitors, alkaline compounds, phosphates and condensate protecting amines. In addition to combining alkalinity control, scale inhibitors, and deposit control, LIQUIVAP TREAT provides protection from corrosion. It efficiently treats Boiler/Steam Water in System lines and Condensate. It provides an excellent and very practical way of treatment, using only one product. Scale, corrosion and foaming are the main problems in Marine Boilers, due to the fact that when the water evaporates, precipitation of salts occurs rapidly.
 
If these salts were not treated they could be turned into very hard scale deposits, which would reduce the system ability to produce steam. This can result in a low volume of steam, which can delay critical operations
on the vessel where steam is used as the ‘driving force’, and will certainly increase the cost of heating, as more fuel would be required to produce the same result.If the boiler water is not treated properly, this would be rapidly resulting in the whole system deterioration due to corrosion.
 
LIQUIVAP TREAT controls the problems described above by achieving the appropriate chemical concentrations and their correct monitoring will maintain the system in a good working condition. When properly dosed it creates the required Alkalinity and Phosphate concentration levels to avoid the acidic “attack” and salts precipitation respectively.
 
Furthermore, it releases into the system a volatile amine inhibitor that circulates with steam in the tube lines, protecting the steel metallic surfaces and condensate system from Carbonic Acid “attack”. Along with the use of LIQUIVAP TREAT the application of an Oxygen scavenger is required to completely remove the Oxygen dissolved in water, as this is the main cause of corrosion in the system. LIQUIVAP TREAT can be combined  with  Oxygen scavengers and other boiler water treatment chemicals.

Free Delivery / Supply Locations

Oman, Bahrain, Abu Dhabi, Ajman, Al Ain, Dubai, Ras Al-Khaimah, Fujairah, Sharjah, Umm Al Quwain, Ruwais, Khalifa Port, Jebel Ali, DP WORLD, and all UAE ports...