Primary tabs



Product Code ::RXSOL-41-8719-025
Categories: House / HOTEL & CATERING-15
Product Short Description: Anti Microbial and non toxic product which prevents mold growth leaving a protective barrier to prevent future growth
Product Description:

Effectively Cleans and control of mold acts as Anti Micro Bial Product Its highly concentrated advanced formula makes it toughest mold cleaning agent. Concrobium Mold Control effectively results in moisture and damp area.

Concrobium Mold Control dries on surfaces to create an invisible antimicrobial shield that encapsulates and inhibits the growth of mold and fungal spores, prevents new growth, and eliminates musty odors. Concrobium Mold Control contains no bleach, ammonia, alcohol or other VOCs and is suitable for use on most surfaces. Odorless and colorless. Use Concrobium Mold Control to control mold in vulnerable areas such as basements, bathrooms, closets and around windows. For use on hard surfaces such as wallboard, plaster, wood, metal, masonry, concrete and tile.
Product Application:

Concrobium Mold Control is resulting transparent invisible result after dries on surfaces. And effectively prohibits the growth of mold and fungal algae. Its antimicrobial formula makes it popular mold releasing treatment chemicals.

USES OF Concrobium Mold Control

  • Mold remediation in homes, businesses and institutions
  • Mold prevention following flooding or water damage cleanup
  • Pre-treatment of building materials for mold resistance

PREVENTATIVE TREATMENT

To inhibit the growth of mold and mildew on surfaces: 

  1. Apply Concrobium Mold Control on area until evenly wet.
  2. To promote drying and to avoid residue marks, use a clean cloth or paper towel to wipe off excess wetness.
  3. Allow treated surfaces to dry completely. 
Product Dose:

Concrobium Mold Control is most commonly used in basements, bathrooms and laundry rooms and dampness area.  Concrobium Mold Control can be apply by spraying as we as mopping method. Its application is very simple and easy.

DIRECTIONS FOR USE
 
MOLD AND MILDEW CONTROL IN WOOD, WALLBOARD, CONCRETE AND MASONRY (CINDER) BLOCK CONSTRUCTION MATERIALS IN BUILDINGS Concrobium Mold Control is used to treat wood, wallboard, concrete and masonry (cinder) block building materials to inhibit or prevent the growth of mold organisms when the materials are subjected to moist or wet environments. Before applying this product, visible mold growth must be removed and conditions favorable to mold growth must be identified and corrected. 
Product Note:

REMEDIAL TREATMENT SMALL AREAS

Areas of visible growth of less than 30 square feet (the area of a single wall panel) can normally be remediated without elaborate procedures. When these areas are identified, apply Concrobium Mold Control to retard growth and spread of fungal spores and other contaminates until the area can be thoroughly cleaned and remediated. If growth is on ceiling tiles or other such easily removable items of nominal value, remove them and seal them in a plastic bag and dispose with normal trash. If the surface is not easily replaceable: Concrobium Mold Control Mold Control –

Application Instructions

  1. Clean contaminated area to remove surface soil. For best results, and to avoid possible interference from other chemicals, use Concrobium Mold Control for initial cleaning. Use a cloth, cleaning pad or brush suitable to the durability of the surface being cleaned. Remove as much dirt and visible mold as possible.
  2. Apply Concrobium Mold Control on cleaned area until evenly wet.
  3.  To promote drying and to avoid residue marks, use a clean cloth or paper towel to wipe off excess wetness.
  4.  Allow treated surfaces to dry completely. Refer to the Personal Protection Equipment Requirements for Applicators section for the appropriate PPE to wear.

Concrobium Mold Control is suitable for use on most surfaces. If in doubt, perform a test on a small, inconspicuous section. Materials vulnerable to water marks should be wiped immediately after contact with Concrobium Mold Control. Over-application may in some cases result in residue formation, which can be easily wiped away with a Concrobium Mold Control-dampened cloth. Concrobium Mold Control can be applied by hand-spray, paintbrush, roller, immersion, airless sprayer or pressure fogger (approximately one gallon of product should treat a 400 sq. ft. room with a fogger). To maintain protection against re-growth, do not rinse or wash surfaces after treatment. Reapplication of Concrobium Mold Control may be required if surfaces are washed or painted or are otherwise directly exposed to water. Ready to use – do not dilute. Concrobium Mold Control must come in direct contact with mold to be effective.

1 ltr for 100 sq mtr

Industrial area:
Remarks:
Other Equivalent Brand:

Concrobium Mold Control, Algae Control, Mold Control

Product Tag Identification:
Product Useful Area:

Keyword:

Mold Control Chemical manufacturer, Mold Algae Control Chemical supplier

packaing_size:

Concrobium Mold Control manufacturer and supplier in Mumbai, Kandla, Chennai, Visakhapatnam, Kolkata, Fujairah, Dubai, Sharjah, Abudhabi, Muscat, Sohar, Oman, Kenya Africa, Canada

Free Delivery / Supply Locations : 
Oman, Bahrain, Abu Dhabi, Ajman, Al Ain, Dubai, Ras Al-Khaimah, Ras al Khaimah, Fujairah, Sharjah, Umm Al Quwain, Fujairah, Ruwais, Mina (Port) Zayed, Khalifa Port, Kizad, Port Rashid, Jebel Ali Port, DP WORLD, Jebel Ali Free Zone, Khor Fakkan Container Terminal, Port Rashid, Jebel Ali Port, Mina Kalid Port, Khor Fhakan Port ( Khawr Fakkan, Khawr al-Fakkan ), Sharjah Creek, Ajman, Port of Hamriyah, Mina Zayed Port, Mussafah port, Khalifa Port, Umm al-Nar Port, Um Al Quwain Port, Saqr Port, Port of Fujairah, Dibba Port, Jebel Dhanna, Mina Al Hamriya, Mina Rashid, All United Arab Emirates